Skip to content
NoetaINDEPENDENT STUDY LIBRARY

CITB ยท Health, safety and environment test for operatives

Occupational health

100 questions in this part of the Health and Safety Test (CSCS) bank. Every answer below is the one the bank holds, and the document under each question is where it was written from. They are written from those documents; they are not the questions of the real test, which are not published.

Practise the whole bank in the browserThe same bank as an Android app, on Google Play

All 100 questions

  1. 1. Occupational healthcscs-188

    Blue smoke is coming from a site generator. What does that usually mean?

    • AThe engine is poorly serviced or tunedAnswer
    • BThe engine is running at its best
    • CThe fuel tank is nearly empty
    • DThe engine has only just been started from cold

    Black smoke points to a mechanical fault, and white smoke that clears as the machine warms up is water and unburnt fuel from a cold start. Blue or black is the signal to get the machine seen to, because that exhaust is what people breathe.

    Sourcehttps://www.hse.gov.uk/construction/healthrisks/cancer-and-construction/diesel-engine-exhaust.htm

  2. 2. Occupational healthcscs-189

    On a construction site, where does most diesel exhaust come from?

    • AHand held power tools
    • BSite cabin heaters
    • CGenerators and heavy vehiclesAnswer
    • DWelding sets

    The risk climbs when that plant runs for long stretches in an enclosed space, and when the exhaust shows colour. Short exposure irritates the eyes and airways and passes off in fresh air. Years of it do not pass off.

    Sourcehttps://www.hse.gov.uk/construction/healthrisks/cancer-and-construction/diesel-engine-exhaust.htm

  3. 3. Occupational healthcscs-190

    What is the long term danger of breathing diesel exhaust year after year?

    • APermanent loss of hearing
    • BDamage to the joints
    • CNothing, once you are used to it
    • DA raised risk of lung cancerAnswer

    Shorter spells bring coughing, chestiness and breathlessness, worst where there is coloured smoke. Research put more than two hundred early deaths among construction workers in one year down to this exposure.

    Sourcehttps://www.hse.gov.uk/construction/healthrisks/cancer-and-construction/diesel-engine-exhaust.htm

  4. 4. Occupational healthcscs-191

    What causes most skin cancer among construction workers?

    • ACement dust on the hands
    • BCold wind in winter
    • CUltraviolet radiation from sunlightAnswer
    • DVibration from hand tools

    Time spent outdoors is what puts this trade in the at risk group. Chemicals come second, mainly the tars once used in surfacing work. Cover up, keep to the shade in the middle of the day, and watch the skin for changes.

    Sourcehttps://www.hse.gov.uk/construction/healthrisks/cancer-and-construction/skin-cancers.htm

  5. 5. Occupational healthcscs-192

    What is the most common sign of a malignant melanoma?

    • AA rash across both forearms
    • BA dry cough that will not clear
    • CSwelling in the ankles at night
    • DA new mole, or a change in one you haveAnswer

    These often have an odd shape and more than one colour, and they can itch or bleed. It is the rarer of the two kinds but the serious one, because it spreads. Caught early, surgery often works, so getting it looked at matters.

    Sourcehttps://www.hse.gov.uk/construction/healthrisks/cancer-and-construction/skin-cancers.htm

  6. 6. Occupational healthcscs-193

    Which chemicals used on site have been the biggest cause of skin cancer?

    • AModern water based emulsion paints
    • BCoal tar and pitch productsAnswer
    • COrdinary washing detergents
    • DPlasterboard adhesives

    The risk from these has dropped a long way since petroleum based products replaced the tars. Sunlight is now the larger cause by far. Either way the damage shows up years afterwards, not on the day it is done.

    Sourcehttps://www.hse.gov.uk/construction/healthrisks/cancer-and-construction/skin-cancers.htm

  7. 7. Occupational healthcscs-194

    Which way of applying a polyurethane paint puts the most isocyanate into the air?

    • ABrushing
    • BRollering
    • CTrowelling
    • DSprayingAnswer

    Hand tools keep exposure lower, which is why they are preferred wherever the finish allows. The tighter the space, the worse any method becomes. Where ventilation is not enough, properly fitted breathing protection is needed on top.

    Sourcehttps://www.hse.gov.uk/construction/healthrisks/hazardous-substances/isocyanates.htm

  8. 8. Occupational healthcscs-195

    Which lasting illness can isocyanates bring on?

    • ALoss of hearing
    • BVibration white finger
    • COccupational asthmaAnswer
    • DA hernia

    The same substances irritate the eyes, nose and throat and cause skin trouble. Once someone reacts to them they have to be kept away from the work altogether, because there is no safe level for that person after that.

    Sourcehttps://www.hse.gov.uk/construction/healthrisks/hazardous-substances/isocyanates.htm

  9. 9. Occupational healthcscs-196

    Isocyanate product gets onto the skin. What must not be used to clean it off?

    • ASolventsAnswer
    • BSoap and water
    • CSkin cream after washing
    • DDisposable wipes then washing

    They carry the substance inwards instead of taking it away. Wash it off as soon as it happens, wash again at breaks and at the end of the shift, and make sure the site has facilities good enough to do that properly.

    Sourcehttps://www.hse.gov.uk/construction/healthrisks/hazardous-substances/isocyanates.htm

  10. 10. Occupational healthcscs-197

    Besides breathing the vapour, how else can solvents get into the body?

    • AOnly through open cuts
    • BThrough the ears
    • CThrough the skinAnswer
    • DThey cannot get in any other way

    They also go in on contaminated food, drink and cigarettes, which is why hands come first at break time. Liquid left on the skin long enough burns it or brings on dermatitis, and vapour in the eyes causes inflammation.

    Sourcehttps://www.hse.gov.uk/construction/healthrisks/hazardous-substances/solvents.htm

  11. 11. Occupational healthcscs-198

    What can a high concentration of solvent vapour in the air do?

    • ACause a mild rash only
    • BNothing at all, if the smell is faint
    • COnly affect people with asthma
    • DCause unconsciousness and deathAnswer

    Lower levels bring headaches, dizziness, nausea and irritation of the eyes, lungs and skin, and a dizzy worker on a site is an accident waiting to happen. Years of it can damage the liver, the kidneys and the nervous system.

    Sourcehttps://www.hse.gov.uk/construction/healthrisks/hazardous-substances/solvents.htm

  12. 12. Occupational healthcscs-199

    Painting a room with a spray gun rather than a brush changes the risk how?

    • ALess solvent goes into the air
    • BIt makes no difference at all
    • CMore solvent goes into the airAnswer
    • DThe paint becomes non hazardous

    The job also gets through more paint in less time, so exposure rises twice over. A closed room makes it worse again. Where a water based or solvent free product will do the work, that is the first thing to try.

    Sourcehttps://www.hse.gov.uk/construction/healthrisks/hazardous-substances/solvents.htm

  13. 13. Occupational healthcscs-200

    What is the daily exposure action value for hand-arm vibration?

    • A0.5 m/s2 A(8)
    • B5.0 m/s2 A(8)
    • CThere is no action value
    • D2.5 m/s2 A(8)Answer

    Above that figure the employer has to bring in a planned programme to cut exposure: other methods, lower vibration tools, shorter spells on the machine. Below it the risk is low and only cheap and simple steps are expected.

    Sourcehttps://www.hse.gov.uk/vibration/hav/regulations.htm

  14. 14. Occupational healthcscs-201

    Hand-arm vibration also has a ceiling that must never be passed. What is it?

    • A2.5 m/s2 A(8)
    • B5.0 m/s2 A(8)Answer
    • C8.0 m/s2 A(8)
    • DThere is no such figure

    It is worked out over an eight hour day and sits at twice the level where action becomes compulsory. Both figures come from the Control of Vibration at Work Regulations 2005, which also cover whole-body vibration.

    Sourcehttps://www.hse.gov.uk/vibration/hav/regulations.htm

  15. 15. Occupational healthcscs-202

    Who has to be given health surveillance for hand-arm vibration?

    • AOnly workers over the age of fifty
    • BOnly those who have already reported symptoms
    • CNobody, because it is voluntary
    • DAnyone likely to be regularly exposed above the action valueAnswer

    It starts with a questionnaire about early symptoms and goes further if the answers point that way. The point is to catch the damage while it can still be stopped, and to show whether the controls in place are working.

    Sourcehttps://www.hse.gov.uk/vibration/hav/protect.htm

  16. 16. Occupational healthcscs-236

    Plasterboard has to be moved by hand on a job. What does the guidance say?

    • AMake it a two person operationAnswer
    • BCarry one board at a time overhead
    • CUse the strongest worker on the gang
    • DDrag the boards along the floor

    Carrying handles and trolleys help further. Better still is getting the boards in mechanically before the openings are closed up, and planning the loading bays and access points that make that possible.

    Sourcehttps://www.hse.gov.uk/construction/healthrisks/physical-ill-health-risks/manual-handling-specific-tasks-plasterboard.htm

  17. 17. Occupational healthcscs-237

    How heavy can a special thermal or acoustic plasterboard be?

    • AAbout 5kg each
    • BAbout 12kg each
    • CUp to 50kg eachAnswer
    • DNever more than 20kg

    That is why suppliers are asked to mark the unit weight on the boards, and why the lightest board that still meets the specification is the one to order. Weight you cannot see is weight nobody plans for.

    Sourcehttps://www.hse.gov.uk/construction/healthrisks/physical-ill-health-risks/manual-handling-specific-tasks-plasterboard.htm

  18. 18. Occupational healthcscs-238

    What do the work equipment regulations require of a tool used for repetitive work?

    • AIt is bought new for each job
    • BIt is the lightest tool on the market today
    • CIt is shared between two workers
    • DIt is suitable for the task being doneAnswer

    Suitable includes not putting undue strain on the person using it. Rapid or prolonged repetition, awkward or fixed postures and heavy force are what turn an everyday tool into an injury over time.

    Sourcehttps://www.hse.gov.uk/construction/healthrisks/physical-ill-health-risks/repetitive-work.htm

  19. 19. Occupational healthcscs-239

    Why does the length of a repetitive task matter so much?

    • AShort spells use less electricity
    • BLong spells wear the tool out faster
    • CShort spells let the body recoverAnswer
    • DLong spells need more supervision

    As the time on the task grows, so does the chance of injury. Both parts count: how long it runs in one shift, and how many days in a row it is repeated. Cold conditions and vibrating tools make it worse again.

    Sourcehttps://www.hse.gov.uk/construction/healthrisks/physical-ill-health-risks/repetitive-work.htm

  20. 20. Occupational healthcscs-240

    What is exposure monitoring on a site for?

    • AChecking how healthy a worker is
    • BCounting how many people are on the site
    • CTiming how long a job takes
    • DMeasuring dust or noise during a taskAnswer

    It measures the work, not the person. The state of somebody's health is looked at through health surveillance, which is a separate thing with a separate purpose. Air sampling in the breathing zone is the commonest method.

    Sourcehttps://www.hse.gov.uk/construction/healthrisks/managing-essentials/exposure-monitoring.htm

  21. 21. Occupational healthcscs-241

    Which condition is construction near the top of the league table for?

    • AFood poisoning at work
    • BHand-Arm Vibration SyndromeAnswer
    • CEye strain from screens
    • DMotion sickness

    Grinders, breakers and pedestrian saws are the usual sources. The damage runs to circulation, nerves and muscle in the hands and arms, and it can take away the ability to grip properly for good.

    Sourcehttps://www.hse.gov.uk/construction/healthrisks/physical-ill-health-risks/key-points.htm

  22. 22. Occupational healthcscs-242

    How does work related cancer compare with accidents in construction?

    • AFar more workers die in site accidents
    • BThe two are about equal
    • CNeither causes many deaths
    • DFar more workers die of the cancersAnswer

    The estimate is roughly a hundred deaths from work related cancer for every fatal accident on site. The gap between the exposure and the illness is often ten to forty years, which is why nobody feels it happening at the time.

    Sourcehttps://www.hse.gov.uk/construction/healthrisks/cancer-and-construction/key-points.htm

  23. 23. Occupational healthcscs-243

    At what height should block laying be set up?

    • AAbove shoulder height
    • BAt ground level only
    • CBetween chest and knee heightAnswer
    • DWherever the gang prefers

    Working above the shoulder or below the knee is where the strain climbs, and laying blocks is repetitive enough already. Platforms are set to keep the work in that band, and blocks are carried close to the body, never up a ladder.

    Sourcehttps://www.hse.gov.uk/construction/healthrisks/physical-ill-health-risks/manual-handling-specific-tasks-blocks-masonry-units.htm

  24. 24. Occupational healthcscs-244

    Under COSHH, what comes before controlling exposure to a hazardous substance?

    • APreventing the exposure altogetherAnswer
    • BIssuing gloves and a mask
    • CWriting it into the method statement first
    • DTelling the workers about it

    Prevention is done first of all by substitution: replacing the substance or the process with one that removes or reduces the risk. Only where prevention is not reasonably practicable does the duty become one of adequate control.

    Sourcehttps://www.legislation.gov.uk/uksi/2002/2677/regulation/7

  25. 25. Occupational healthcscs-245

    Where does personal protective equipment sit in the COSHH order of priority?

    • AFirst, before anything else is tried
    • BSecond, ahead of ventilation
    • CLast, in addition to the other measuresAnswer
    • DIt is not mentioned in COSHH

    Work processes, engineering controls and suitable equipment come first, then control at source with ventilation and organisational measures. Kit for the individual is what is left when those cannot do the job on their own.

    Sourcehttps://www.legislation.gov.uk/uksi/2002/2677/regulation/7

  26. 26. Occupational healthcscs-246

    When must an employer give health and safety training under the management regulations?

    • AOnce every five years, whatever happens
    • BOnly after an accident on site
    • COnly if the worker asks for it
    • DOn recruitment and on facing new risksAnswer

    New risks means a change of job, new equipment, new technology or a new system of work. The training is repeated where that is appropriate, kept up to date with the risks, and given during working hours.

    Sourcehttps://www.legislation.gov.uk/uksi/1999/3242/regulation/13

  27. 27. Occupational healthcscs-26

    A simple sign that noise on site may be harmful is when workers have to do what?

    • AWear ear plugs by choice
    • BShout to be heard two metres apartAnswer
    • CTurn off the radio to talk
    • DMove to another part of the site

    If you must raise your voice to be heard at about two metres for part of the day, the noise is probably high enough to act on. Using loud tools for more than half an hour a day is another sign. Neither needs a meter to spot.

    Sourcehttps://www.hse.gov.uk/construction/healthrisks/physical-ill-health-risks/noise.htm

  28. 28. Occupational healthcscs-27

    What happens to hearing damaged by noise at work?

    • AIt comes back after a long rest
    • BIt can be repaired by surgery
    • CIt does not come backAnswer
    • DA hearing aid restores it fully

    There is no cure. A hearing aid helps but does not give back natural hearing, especially where there is background noise. That is why the controls have to be used on the day, not started once you notice a problem.

    Sourcehttps://www.hse.gov.uk/construction/healthrisks/physical-ill-health-risks/noise.htm

  29. 29. Occupational healthcscs-28

    A site hands out ear defenders and says the noise problem is solved. What is wrong with that?

    • ADefenders must be issued in pairs
    • BProtection is not a substitute for cutting noiseAnswer
    • CDefenders only work below 80 decibels
    • DOnly the site manager may issue them

    Hearing protection is the last step, not the first. It can be worn wrongly, taken off or damaged, so it must not be the only control. Quieter tools, screens, distance and shorter exposure all come before it.

    Sourcehttps://www.hse.gov.uk/construction/healthrisks/physical-ill-health-risks/noise.htm

  30. 30. Occupational healthcscs-29

    At what daily or weekly average must an employer set up hearing protection zones?

    • A75 dB(A)
    • B80 dB(A)
    • C85 dB(A)Answer
    • D95 dB(A)

    The Control of Noise at Work Regulations 2005 fix that point at 85, and at that level protection must be given and the zone marked. Wearing it inside a marked zone is not optional. The absolute ceiling, counting what protection takes off, is 87.

    Sourcehttps://www.hse.gov.uk/noise/regulations.htm

  31. 31. Occupational healthcscs-30

    Noise damage sometimes leaves people with a constant ringing in the ears. What is that called?

    • ATinnitusAnswer
    • BVertigo
    • CSilicosis
    • DDermatitis

    It can become permanent and there is no way to switch it off. Some people find it worse than the lost hearing itself, because it never stops. Hearing checks are there to catch early damage before it gets that far.

    Sourcehttps://www.hse.gov.uk/noise/keyfacts.htm

  32. 32. Occupational healthcscs-31

    Do gloves protect your hands from the vibration of a breaker?

    • AYes, thick gloves absorb most of it
    • BYes, if they carry a vibration rating
    • CNo, but they keep the hands warmAnswer
    • DNo, and they make the risk worse

    Gloves are worth wearing because warm hands have better blood flow, which helps. They do not cut the vibration going into your hand and arm. The real controls are a different method, a better tool and less time on the trigger.

    Sourcehttps://www.hse.gov.uk/construction/healthrisks/physical-ill-health-risks/vibration.htm

  33. 33. Occupational healthcscs-310

    Which is bigger across a year in construction: days lost to illness or days lost to injury?

    • ADays lost to illnessAnswer
    • BDays lost to injury
    • CThey come out about equal
    • DNobody counts either one

    Injury is what gets noticed because it happens in a moment, but days lost to illness outnumber the rest every year, which is why health carries its own set of duties.

    Sourcehttps://www.hse.gov.uk/construction/healthrisks/key-points.htm

  34. 34. Occupational healthcscs-311

    Why does building work carry health risks that a factory does not?

    • ABecause the work is always outdoors
    • BBecause the sites vary from job to jobAnswer
    • CBecause the hours are always longer
    • DBecause the pay is by the piece

    A factory hazard sits still and can be engineered out once. Not so here, because the sites vary from job to job, and even two corners of the same site differ, so the assessment has to be made afresh.

    Sourcehttps://www.hse.gov.uk/construction/healthrisks/key-points.htm

  35. 35. Occupational healthcscs-312

    Does the law set a maximum weight one person may lift by hand?

    • AYes, twenty five kilograms for men
    • BNo, it sets no weight limit at allAnswer
    • CYes, twenty kilograms for everyone
    • DYes, but only for outdoor work

    Weight on its own does not decide the danger, and the law is silent here: it sets no weight limit at all. The guideline figures are filters for sorting jobs, not safe limits.

    Sourcehttps://www.hse.gov.uk/msd/manual-handling-risk-filters.htm

  36. 36. Occupational healthcscs-313

    Which of these belongs to the review stage of managing health risks?

    • AIdentifying the hazards in the work
    • BChoosing a less harmful material
    • CMaintaining the controls in useAnswer
    • DWriting the overall strategy

    Review asks whether what was put in place still works, so maintaining the controls in use sits there, next to supervising, monitoring and acting on whatever turns up.

    Sourcehttps://www.hse.gov.uk/construction/healthrisks/managing-essentials/managing-essentials.htm

  37. 37. Occupational healthcscs-314

    HSE sums up the review stage in a short phrase. Which one?

    • AEveryone has a role to play
    • BIll-health can be prevented
    • CManage risk not lifestyles
    • DControl the risks not the symptomsAnswer

    Treating the cough and leaving the dust in the air changes nothing, which is the whole point of control the risks not the symptoms.

    Sourcehttps://www.hse.gov.uk/construction/healthrisks/managing-essentials/managing-essentials.htm

  38. 38. Occupational healthcscs-315

    Where there is a risk of musculoskeletal disorders, is health monitoring compulsory?

    • AYes, monthly, for every worker
    • BYes, but only above fifty staff
    • CNo, though it is often usefulAnswer
    • DNo, and it is discouraged

    It sits outside the legal minimum, so no, though it is often useful for catching trends early and for checking that the controls put in place are working.

    Sourcehttps://www.hse.gov.uk/msd/health-monitoring.htm

  39. 39. Occupational healthcscs-316

    Why does the law want prevention looked at before control?

    • ABecause it is written into every contract
    • BBecause it works better and often costs lessAnswer
    • CBecause insurers insist on it in writing
    • DBecause control measures are banned first

    Removing a hazard settles it for everybody at once, so prevention comes first because it works better and often costs less than policing a risk for the length of a job.

    Sourcehttps://www.hse.gov.uk/construction/healthrisks/managing-essentials/control-the-risks.htm

  40. 40. Occupational healthcscs-317

    What does HSE say about leaning on protective equipment alone?

    • AIt is the normal way to control health risk
    • BIt is fine where the work is short
    • CIt needs justifying and is not the normAnswer
    • DIt is forbidden on construction sites

    Equipment guards only the person wearing it, and only while it is worn properly, so as a sole measure it needs justifying and is not the norm.

    Sourcehttps://www.hse.gov.uk/construction/healthrisks/managing-essentials/control-the-risks.htm

  41. 41. Occupational healthcscs-318

    Which of these counts as a control once a health risk cannot be prevented?

    • APaying a bonus for finishing early
    • BExtending the working day instead
    • CLeaving the job to the youngest man
    • DRotating the people doing the taskAnswer

    Exposure builds up with time on the tool, so rotating the people doing the task cuts each man's dose, alongside better equipment and keeping others clear of the work.

    Sourcehttps://www.hse.gov.uk/construction/healthrisks/managing-essentials/control-the-risks.htm

  42. 42. Occupational healthcscs-319

    What does HSE call the last link between planning the work and doing it properly?

    • AThe method statement
    • BThe site supervisorAnswer
    • CThe induction
    • DThe permit to work

    Plans stop at the site hut unless somebody carries them onto the job, and the site supervisor is that final link before the work actually happens.

    Sourcehttps://www.hse.gov.uk/construction/healthrisks/managing-essentials/review-the-controls.htm

  43. 43. Occupational healthcscs-32

    A worker has lost feeling in the fingers after years of using breakers. What is the outlook?

    • AIt clears up after a few months off tools
    • BThe harm to the hands is largely permanentAnswer
    • CIt only affects people over sixty
    • DIt goes once the weather warms up

    Hand Arm Vibration Syndrome damages nerves, blood vessels and joints, and that damage does not undo itself. People lose the ability to do fine work and to hold things safely. Everything useful happens before the symptoms arrive.

    Sourcehttps://www.hse.gov.uk/construction/healthrisks/physical-ill-health-risks/vibration.htm

  44. 44. Occupational healthcscs-320

    When checking that workers understand the risks, who needs the closer attention?

    • AThe longest serving tradesmen
    • BAnyone who works overtime often
    • CNew, young or non-English speakersAnswer
    • DThose who live nearest the site

    Understanding cannot be read off a signature on a register, so new, young or non-English speakers get the closer look, along with anyone inexperienced.

    Sourcehttps://www.hse.gov.uk/construction/healthrisks/managing-essentials/review-the-controls.htm

  45. 45. Occupational healthcscs-321

    Which parts of the body do musculoskeletal disorders most often reach?

    • AThe eyes, ears and airways
    • BThe heart, lungs and liver
    • CThe skin and the scalp only
    • DThe back, limbs and jointsAnswer

    These conditions live in the frame that does the lifting, so the back, limbs and joints take the damage: lower back, shoulders, arms, hips, knees and feet.

    Sourcehttps://www.hse.gov.uk/msd/msds.htm

  46. 46. Occupational healthcscs-322

    What does HSE call the most efficient way of controlling noise at work?

    • AHanding out ear defenders to all
    • BCutting it at source by designAnswer
    • CShortening the working week
    • DMoving the site further away

    Protection worn on the head is the last line rather than the first, so the guidance points to cutting it at source by design: changing the process, damping vibration and keeping time in noisy areas down.

    Sourcehttps://www.hse.gov.uk/noise/keyfacts.htm

  47. 47. Occupational healthcscs-323

    What does HSE say about simply telling workers that something is a risk?

    • AIt is enough if it is in writing
    • BIt is enough if repeated weekly
    • CIt is only needed for new starters
    • DIt is not enough on its ownAnswer

    The people doing the job daily can see what will actually work, so telling them is not enough on its own: they have to be brought into finding the answer.

    Sourcehttps://www.hse.gov.uk/construction/healthrisks/managing-essentials/assess-the-risks.htm

  48. 48. Occupational healthcscs-324

    What is health surveillance there to do?

    • ACatch harm early and test the controlsAnswer
    • BProve a worker was already ill
    • CDecide who gets the overtime
    • DReplace the need for an assessment

    It is an ongoing check on people exposed to something harmful, so its value is to catch harm early and test the controls, showing which of them need improving.

    Sourcehttps://www.hse.gov.uk/construction/healthrisks/managing-essentials/health-surveillance.htm

  49. 49. Occupational healthcscs-325

    Sprayed paint throws off droplets and solvent vapour at the same time. Why does that matter?

    • AThe form decides who pays for it
    • BThe form decides the right controlsAnswer
    • CThe form changes the permit needed
    • DThe form sets the price of the paint

    A mask that stops droplets can let vapour through untouched, so the form decides the right controls, and one operation may produce two forms at once.

    Sourcehttps://www.hse.gov.uk/construction/healthrisks/hazardous-substances/key-points.htm

  50. 50. Occupational healthcscs-326

    What is the most commonly reported cause of over seven day injuries in the industry?

    • AFalls from a ladder
    • BHandling and carrying loadsAnswer
    • CBeing struck by a vehicle
    • DContact with electricity

    It is the ordinary background of the trade rather than a dramatic event, yet handling and carrying loads still tops the list of injuries that keep people off work more than a week.

    Sourcehttps://www.hse.gov.uk/construction/healthrisks/physical-ill-health-risks/key-points.htm

  51. 51. Occupational healthcscs-327

    How heavy can a single concrete kerb be?

    • AAbout 15kg each
    • BAbout 30kg each
    • CAbout 45kg each
    • DMore than 70kg eachAnswer

    The weight is what makes the task dangerous, not the posture alone: concrete kerbs run to more than 70kg each, and natural stone paving can be heavier still.

    Sourcehttps://www.hse.gov.uk/construction/healthrisks/physical-ill-health-risks/manual-handling-specific-tasks-kerbs-paving.htm

  52. 52. Occupational healthcscs-328

    What does HSE call the preferred answer to laying heavy kerbs and slabs?

    • ATwo men lifting together
    • BA short shift on the task
    • CFully mechanised laying systemsAnswer
    • DA back belt for each worker

    Technique training does not make a heavy unit lighter, so fully mechanised laying systems such as vacuum devices or grabs are preferred wherever the weight cannot be designed out.

    Sourcehttps://www.hse.gov.uk/construction/healthrisks/physical-ill-health-risks/manual-handling-specific-tasks-kerbs-paving.htm

  53. 53. Occupational healthcscs-329

    A worker's back has been aching for a fortnight. What does HSE ask them to do?

    • AReport it as soon as possibleAnswer
    • BWait a month and see
    • CChange trade if it persists
    • DBuy a support belt privately

    Most of these problems clear up completely when they are caught early, so the advice is to report it as soon as possible to a manager or a safety representative.

    Sourcehttps://www.hse.gov.uk/msd/workers-msds.htm

  54. 54. Occupational healthcscs-33

    What are the early warning signs of vibration damage that you should report?

    • AAching shoulders after a long shift
    • BTingling and numbness in the fingersAnswer
    • CSore eyes in dusty conditions
    • DA cough that starts in the morning

    Tingling and numbness come first, often at night, followed by losing grip strength. Fingertips going white in the cold and hurting as they recover is the next stage. Reporting early is what stops it becoming permanent.

    Sourcehttps://www.hse.gov.uk/vibration/hav/yourhands.htm

  55. 55. Occupational healthcscs-330

    What does HSE mean by presenteeism?

    • AGoing to work while unwellAnswer
    • BArriving early to look keen
    • CSigning in for another man
    • DStaying late without extra pay

    It is the belief that going to work while unwell is what is expected, and HSE notes those rates often run higher than the sickness absence a firm actually records.

    Sourcehttps://www.hse.gov.uk/construction/healthrisks/managing-essentials/wellbeing.htm

  56. 56. Occupational healthcscs-331

    Above what daily level must a worker never be exposed to noise, counting the protection worn?

    • A80 dB(A)
    • B85 dB(A)
    • C87 dB(A)Answer
    • D90 dB(A)

    This one is measured with the hearing protection taken into account, and 87 dB(A) is the point that must never be passed, unlike the action values that merely set duties running.

    Sourcehttps://www.hse.gov.uk/noise/regulations.htm

  57. 57. Occupational healthcscs-332

    Which of these makes a handling task more dangerous?

    • AKeeping the load close to the waist
    • BWorking on a level, dry floor
    • CHolding the load away from the bodyAnswer
    • DSharing the lift between two people

    The further out the weight sits the harder the back has to work, so holding the load away from the body is on the list along with twisting, stooping and reaching overhead.

    Sourcehttps://www.hse.gov.uk/construction/healthrisks/physical-ill-health-risks/manual-handling.htm

  58. 58. Occupational healthcscs-333

    An assessment shows workers at or above the vibration action value. What has to follow?

    • AA note in the accident book
    • BA ban on all power tools
    • CA yearly chest x-ray for each
    • DA planned programme of controlAnswer

    Reaching the action value turns advice into duty, so what follows is a planned programme of control rather than one change of tool and a hope for the best.

    Sourcehttps://www.hse.gov.uk/vibration/hav/protect.htm

  59. 59. Occupational healthcscs-334

    Roughly how many construction workers are believed to die from silica dust each year?

    • AOver 500Answer
    • BAbout 50
    • CAbout 150
    • DAbout 5,000

    The figure is large because the exposure is ordinary: over 500 are believed to die each year from silica raised by cutting, grinding and dry sweeping.

    Sourcehttps://www.hse.gov.uk/construction/healthrisks/hazardous-substances/construction-dust.htm

  60. 60. Occupational healthcscs-34

    Roughly how long a day on hammer action tools puts you above the exposure action value?

    • AAbout 15 minutesAnswer
    • BAbout two hours
    • CAbout four hours
    • DA full working shift

    Hammer action tools are harsh, so the clock runs fast: about a quarter of an hour is enough. Gentler rotary tools take about an hour to reach the same point. Job rotation and breaks are how sites keep under it.

    Sourcehttps://www.hse.gov.uk/vibration/hav/yourhands.htm

  61. 61. Occupational healthcscs-35

    Apart from using better tools, what can a worker do to reduce the risk of vibration damage?

    • ACut down on smokingAnswer
    • BDrink more coffee on breaks
    • CGrip the tool as hard as possible
    • DKeep the hands as cool as possible

    Smoking narrows the blood vessels, and poor circulation is exactly what makes the damage worse. Staying warm and dry, easing off the grip and massaging the fingers at breaks all pull the same way. None of it replaces cutting the trigger time.

    Sourcehttps://www.hse.gov.uk/vibration/hav/yourhands.htm

  62. 62. Occupational healthcscs-36

    How should heavy materials be stored so they are easier to lift?

    • AOn the floor, so nothing can fall
    • BAt waist heightAnswer
    • CAbove head height, out of the way
    • DIn whatever space is left over

    A lift that starts at waist height avoids the stoop and the reach, which is where backs get hurt. Lighter and rarely handled items are the ones that can go on the floor. Laying out the store well removes lifts before anyone trains for them.

    Sourcehttps://www.hse.gov.uk/construction/healthrisks/physical-ill-health-risks/manual-handling.htm

  63. 63. Occupational healthcscs-37

    A firm sends everyone on a lifting technique course and changes nothing else. Is that enough?

    • AYes, technique is the main control
    • BYes, once everyone holds a certificate
    • CNo, technique does not replace other controlsAnswer
    • DNo, because courses expire each year

    Good technique helps, but it is an addition to the controls, not a stand in for them. Mechanical aids, smaller loads, deliveries to the point of use and better layout do the heavy work. Training a man to carry an awkward block still leaves him carrying it.

    Sourcehttps://www.hse.gov.uk/construction/healthrisks/physical-ill-health-risks/manual-handling.htm

  64. 64. Occupational healthcscs-38

    Under the Manual Handling Operations Regulations 1992, what must an employee do?

    • ARefuse any load over 25 kilograms
    • BUse the system of work the employer providesAnswer
    • CAssess each load in writing before lifting
    • DLift only with a second person present

    Where the employer has set up a way of doing the lift, you have to make full and proper use of it. Leaving the barrow in the compound because it is quicker to carry is a breach. The rules do not set one legal weight limit.

    Sourcehttps://www.legislation.gov.uk/uksi/1992/2793/regulation/5

  65. 65. Occupational healthcscs-39

    Why is the fine dust from cutting stone so dangerous?

    • AIt is heavy and settles in the throat
    • BIt is too fine to see in normal lightAnswer
    • CIt only forms when the stone is wet
    • DIt smells strongly, so people avoid it

    The harmful part is respirable crystalline silica, and you cannot see the cloud that matters. That is why people believe the air is clear when it is not. Water suppression or on tool extraction has to run whether or not dust is visible.

    Sourcehttps://www.hse.gov.uk/construction/healthrisks/cancer-and-construction/silica-dust.htm

  66. 66. Occupational healthcscs-40

    Roughly how much silica does sandstone contain?

    • ALess than 5%
    • BAbout 10%
    • CMore than 70%Answer
    • DNone at all

    Sandstone is mostly silica, while granite is nearer 15 to 30 per cent. Bricks, tiles, concrete and mortar all contain it too. Knowing the material tells you how hard the dust control has to work.

    Sourcehttps://www.hse.gov.uk/construction/healthrisks/cancer-and-construction/silica-dust.htm

  67. 67. Occupational healthcscs-401

    What counts as drug and alcohol misuse at work?

    • AIllegal drugs, drink, medicines and solventsAnswer
    • BIllegal drugs and nothing else
    • CDrinking during working hours and nothing else
    • DOnly being dependent on drink or drugs

    Misuse is wider than the illegal drugs most people think of first, and it is not the same as dependence. Prescription medicine and solvents count too, because they change how fast you react and how well you judge a risk. Warning signs on site are frequent absences, a change in behaviour, dips in output and more near misses.

    Sourcehttps://www.hse.gov.uk/alcoholdrugs/index.htm

  68. 68. Occupational healthcscs-402

    A machine operator asks for help with a drink problem. What may happen to his job?

    • AMove him to other work, at least for nowAnswer
    • BLeave him on the machine and say nothing
    • CCut his pay until the treatment ends
    • DSend him home without pay for a month

    Safety critical work is where misuse could end badly: machinery, electrical gear, ladders, driving and lifting plant. Asking for help should not cost a man his job, but it can mean a temporary move off that kind of work. The move protects him and everybody working around him while he gets sorted.

    Sourcehttps://www.hse.gov.uk/alcoholdrugs/look-at-safety-critical-work.htm

  69. 69. Occupational healthcscs-403

    Your firm wants to screen the workforce for drugs. What is the position on consent?

    • AEmployees must agree to the screeningAnswer
    • BConsent is only needed for night workers
    • CConsent is assumed once you sign on
    • DNo consent is needed on a building site

    Nobody can force a sample out of you, but refusing when the employer has good grounds to test can bring disciplinary action. Testing on its own solves nothing either, so it only makes sense as part of the wider health and safety policy. Samples also have to be taken and handled so they cannot be swapped or tampered with.

    Sourcehttps://www.hse.gov.uk/alcoholdrugs/screening-testing-drugs-alcohol.htm

  70. 70. Occupational healthcscs-404

    A man tells his supervisor he has a drug problem. What should the site policy aim to do?

    • AHelp and support him rather than sack himAnswer
    • BSack him at the end of the shift
    • CMove him to nights so nobody sees
    • DWait and see if he has an accident

    Dependence is treated as a medical problem, so the first step is help and not the gate. A firm that sacks a man without trying to help him can be found by a tribunal to have dismissed him unfairly. The policy still has to say where support ends and discipline begins, so everyone knows the rules before they are needed.

    Sourcehttps://www.hse.gov.uk/alcoholdrugs/develop-policy.htm

  71. 71. Occupational healthcscs-405

    Somebody is dealing drugs on site. What does a proper policy say happens next?

    • AIt is reported to the police straight awayAnswer
    • BIt is raised at the next toolbox talk
    • CIt is overlooked while the man works well
    • DIt is dealt with by a written warning

    Support is for the person with a habit, not for the man selling. Possession and dealing at work are criminal matters, and a policy that spells this out saves any argument on the day. Being clear about the line also makes it easier for someone with a genuine problem to come forward.

    Sourcehttps://www.hse.gov.uk/alcoholdrugs/develop-policy.htm

  72. 72. Occupational healthcscs-406

    A joiner asks the firm for help with drink. What privacy can he expect?

    • AThe same as for any other medical conditionAnswer
    • BNone, because drink is his own doing
    • CIt depends how long he has worked there
    • DOnly if the firm has its own doctor

    Drug and alcohol dependence are recognised medical problems, so they are handled as discreetly as anything else a doctor would see. Men only ask for help when they trust that it will be kept quiet. Where it gets talked about in the canteen the problem simply goes underground and stays on the tools.

    Sourcehttps://www.hse.gov.uk/alcoholdrugs/support-employees.htm

  73. 73. Occupational healthcscs-407

    How is stress defined for health and safety purposes?

    • AA bad reaction to too much pressure or demandAnswer
    • BAny pressure at all during a working day
    • CAn illness you catch from other people
    • DA weakness in men who cannot cope

    Pressure by itself is just work; stress is what happens when a man cannot cope with the pressure put on him. Stress is not an illness, but it can make you ill, and what floors one person leaves the next one untouched. That is why the answer is in how the job is set up rather than in who is doing it.

    Sourcehttps://www.hse.gov.uk/stress/overview.htm

  74. 74. Occupational healthcscs-408

    Six areas of work design are known to drive stress levels. Which are they?

    • ADemands, control, support, relationships, role, changeAnswer
    • BPermits, signage, first aid, audits, tools, training
    • CPay, travel, parking, canteens, weather, overtime
    • DDust, noise, vibration, heat, cold and lighting

    These are the things a firm can actually change: how much work there is, how much say you get, what backup is behind you, how people treat each other, whether your job is clear, and how change is handled. Get them wrong and it will grind down whoever you put in the job. That is why the fix starts with a risk assessment and not with a pep talk.

    Sourcehttps://www.hse.gov.uk/stress/overview.htm

  75. 75. Occupational healthcscs-409

    What does the law require your employer to do about stress at work?

    • AAssess the risk and share the findingsAnswer
    • BNothing, it is a private matter
    • COnly act once somebody goes off sick
    • DPut the whole crew on a short course

    It is the same duty as for dust or work at height: look at the risk, act on it, and tell the workforce what came out of it. Speaking to your manager early gives him the chance to sort it before it grows. If the manager is the cause, a union rep, the office or your own GP are the next doors to knock on.

    Sourcehttps://www.hse.gov.uk/stress/help-employee.htm

  76. 76. Occupational healthcscs-41

    After asbestos, what is the biggest health risk to construction workers?

    • ASilicaAnswer
    • BNoise
    • CDiesel fumes
    • DSolvents

    Heavy or long exposure causes lung cancer, silicosis and long term breathing disease. The amount that does the harm is small, far less than the cloud a saw makes. Cutting, drilling, grinding and polishing are the everyday jobs that produce it.

    Sourcehttps://www.hse.gov.uk/construction/healthrisks/cancer-and-construction/silica-dust.htm

  77. 77. Occupational healthcscs-410

    You are near the end of a run of long shifts. What is tiredness doing to you?

    • ASlowing reactions and hiding risk from youAnswer
    • BOnly leaving you wanting a lie in
    • CChanging your mood but not your judgement
    • DWearing off as soon as you get moving

    Being worn out eats into reaction time, attention, memory and coordination, and it makes people rate a hazard lower than it really is. That mix is how a man walks under a suspended load or misses a machine that is already moving. It has been the root cause of some of the worst disasters on record, so it is treated as a hazard in its own right.

    Sourcehttps://www.hse.gov.uk/humanfactors/topics/fatigue.htm

  78. 78. Occupational healthcscs-411

    A man volunteers for a seventh twelve hour shift in a row. Who has to deal with the danger in that?

    • AThe employer, whatever the man wantsAnswer
    • BThe man, because he offered
    • CNobody, once the hours are agreed
    • DThe client who set the programme

    Being willing to do the hours does not make them safe, and simply staying inside the Working Time Regulations is not enough on its own. Injuries go up on nights, after a run of shifts, on long shifts and where breaks are too short. So hours, overtime and shift swaps have to be planned and recorded, not left to whoever puts his hand up.

    Sourcehttps://www.hse.gov.uk/humanfactors/topics/fatigue.htm

  79. 79. Occupational healthcscs-42

    Breathing construction dust regularly is linked to which kinds of illness?

    • AShort term coughs that always clear up
    • BSkin rashes and eye irritation only
    • CLung cancer, asthma and other lung diseaseAnswer
    • DNothing, if you are otherwise healthy

    The diseases build up quietly over years and then do not go away. They disable people and shorten lives. That is why dust is treated as a health risk to control at source, not a nuisance to put up with.

    Sourcehttps://www.hse.gov.uk/construction/healthrisks/hazardous-substances/construction-dust.htm

  80. 80. Occupational healthcscs-43

    Wet cement gets inside a worker's boot and stays against the skin. What is the risk?

    • AMild itching for a day or two
    • BA serious burn or ulcer can develop fastAnswer
    • CNothing, cement is harmless when wet
    • DThe skin will simply dry out

    Wet cement is strongly alkaline and it keeps working while it is trapped. Bad cases have needed skin grafts, and in the worst cases a limb has been lost. Boots should be high enough to keep it out and trousers worn over the top.

    Sourcehttps://www.hse.gov.uk/construction/healthrisks/hazardous-substances/cement.htm

  81. 81. Occupational healthcscs-436

    Why does a tight-fitting dust mask have to be fit tested on the person who will wear it?

    • AFaces differ, and one type or size will not seal on everyoneAnswer
    • BThe test proves the filter has not passed its expiry date
    • CThe test is only needed for masks used underground
    • DThe test records who the mask belongs to for stock control

    A mask that leaks protects nobody, and the commonest cause of a leak is poor fit. People come in all shapes and sizes, so no single model or size seals on every face. The test is about the seal between one face and one facepiece, which is why the result belongs to that person and that mask, not to the box.

    Sourcehttps://www.hse.gov.uk/respiratory-protective-equipment/fit-testing-basics.htm

  82. 82. Occupational healthcscs-437

    A cutting job needs a tight-fitting mask and the operative has a few days of stubble. What is the effect?

    • AStubble makes a good seal impossible, so dirty air leaks inAnswer
    • BStubble has no effect provided the straps are pulled tight
    • CStubble only matters on powered masks, not simple ones
    • DStubble improves the seal by filling small gaps

    Stubble and beards make it impossible to seal a tight-fitting mask against the face, and air takes the easy route through the gap rather than through the filter. Pulling the straps harder does not fix it. Where there is a good reason for a beard, the answer is loose-fitting powered equipment, not a tighter strap.

    Sourcehttps://www.hse.gov.uk/respiratory-protective-equipment/fit-testing-basics.htm

  83. 83. Occupational healthcscs-438

    An operative was fit tested on one make and size of mask. What follows from that?

    • AThat same make, model, type and size has to be available to themAnswer
    • BAny mask from the same supplier will do afterwards
    • CThe test result covers every mask on that site for a year
    • DThe test needs repeating each morning before work starts

    The test result belongs to one facepiece, so the make, model, type and size the person passed on has to be the one they are actually given. Handing out whatever is left in the store undoes the test completely. Someone who uses more than one type of tight-fitting mask needs a separate test for each type.

    Sourcehttps://www.hse.gov.uk/respiratory-protective-equipment/fit-testing-basics.htm

  84. 84. Occupational healthcscs-439

    Which type of respiratory equipment is the only one suitable where oxygen is lacking?

    • ABreathing apparatus, fed from an independent air supplyAnswer
    • BA powered respirator with a high grade filter
    • CA full-face mask with two filter cartridges
    • DA disposable filtering facepiece rated for fine dust

    A respirator filters the air that is there. If the air is short of oxygen, filtering it changes nothing, and the wearer breathes an atmosphere that cannot keep them alive. Breathing apparatus carries its own supply from a cylinder or compressor, and it is the only choice for that situation. This matters most in confined spaces.

    Sourcehttps://www.hse.gov.uk/respiratory-protective-equipment/types-rpe.htm

  85. 85. Occupational healthcscs-44

    You get mortar splashed on your forearm. What should you do?

    • ALet it dry and brush it off later
    • BWash it off as soon as you canAnswer
    • CRub it in with a dry cloth
    • DCover it with a plaster

    Time against the skin is what causes the damage, so the sooner it is off the better. Wash exposed skin at breaks and at the end of the day as well. If cement gets in the eyes, use the emergency eyewash.

    Sourcehttps://www.hse.gov.uk/construction/healthrisks/hazardous-substances/cement.htm

  86. 86. Occupational healthcscs-440

    What weight limit does the law set for lifting a load by hand at work?

    • ANone, though weight still matters to the assessmentAnswer
    • BA limit of 25 kilograms for men and 16 for women
    • CA limit of 20 kilograms for anyone, in every situation
    • DA limit of 50 kilograms where two people lift together

    There is no legal weight limit, and quoting one on site is a common mistake. The weight of a load is important and feeds into the assessment, but so do the shape, the grip, the distance, the height and the person doing the job. Where injury is a real possibility you may also have to tell people the weight and where the centre of gravity sits.

    Sourcehttps://www.hse.gov.uk/msd/manual-handling/index.htm

  87. 87. Occupational healthcscs-441

    What is the first thing the law asks an employer to do about hazardous manual handling?

    • AAvoid the need for it, so far as is reasonably practicableAnswer
    • BTrain everyone in the correct lifting technique
    • CProvide back supports to everyone who lifts
    • DRecord the weight of every load kept on site

    The order matters: avoid it first, then assess what cannot be avoided, then reduce the risk from what is left as low as reasonably practicable. Training comes into the third step, not the first. Starting with training is starting at the wrong end, because it leaves the hazardous lift in place and puts the burden on the person doing it.

    Sourcehttps://www.hse.gov.uk/msd/manual-handling/index.htm

  88. 88. Occupational healthcscs-442

    Which of these counts as manual handling?

    • APushing, pulling or carrying a load as well as lifting itAnswer
    • BLifting only, since pushing and pulling are separate matters
    • COnly lifting loads from ground level to above the waist
    • DOnly handling loads that weigh more than 10 kilograms

    The definition is transporting or supporting a load by hand or bodily force, and it covers lifting, putting down, pushing, pulling, carrying and moving. A load can be an object, an animal or a person. Dragging a wheelbarrow up a ramp counts just as much as lifting a block, and it is often the pushing that does the damage.

    Sourcehttps://www.hse.gov.uk/msd/manual-handling/index.htm

  89. 89. Occupational healthcscs-443

    You have to lift a load from the ground and cannot avoid it. Where should the load be as you lift?

    • AClose to your waist, with the heaviest side next to youAnswer
    • BHeld out at arm's length so you can see your feet
    • CAbove shoulder height before you start to move
    • DBalanced on one hip so one hand stays free

    Keeping the load close to your waist for as long as possible, with its heaviest side next to your body, is the single change that takes the most strain off the back. If you cannot get close to it, slide it towards you before lifting. Good technique is an addition to the other controls, not a replacement for a lifting aid.

    Sourcehttps://www.hse.gov.uk/msd/manual-handling/good-handling-technique.htm

  90. 90. Occupational healthcscs-444

    What does the guidance say about your back during a lift?

    • ASlight bending is better than a full stoop or a deep squatAnswer
    • BThe back should be locked completely straight throughout
    • CA full stoop is preferred because it is quicker
    • DA deep squat is the only correct way to start a lift

    A slight bend of the back, hips and knees at the start beats either extreme: fully flexing the back, which is stooping, or fully flexing hips and knees, which is deep squatting. Once you begin, do not bend the back any further, which happens when the legs straighten before the load starts to rise. Twisting or leaning sideways with a bent back is the worst combination.

    Sourcehttps://www.hse.gov.uk/msd/manual-handling/good-handling-technique.htm

  91. 91. Occupational healthcscs-45

    What shape of glove is needed when handling cement products?

    • AShort and loose, so hands stay cool
    • BLong and close fitting at the endAnswer
    • CAny glove, as long as it is new
    • DFingerless, for a better grip

    A loose cuff lets cement in, and then the glove holds it against your skin, which is worse than no glove at all. The glove also has to be waterproof and made for strong alkalis. Check it is right for the length of the job.

    Sourcehttps://www.hse.gov.uk/construction/healthrisks/hazardous-substances/cement.htm

  92. 92. Occupational healthcscs-46

    A worker says a tan from working outside shows they are healthy. Is that right?

    • AYes, tanned skin burns less easily
    • BYes, sunlight builds up resistance
    • CNo, a tan is a sign of skin damageAnswer
    • DNo, but only for people with fair skin

    The colour is the skin reacting to harm already done by ultraviolet light. Over years it ages the skin and raises the chance of skin cancer. People of every skin colour also need to watch for overheating and dehydration.

    Sourcehttps://www.hse.gov.uk/skin/sunprotect.htm

  93. 93. Occupational healthcscs-47

    What strength of sunscreen is advised for skin left uncovered outdoors at work?

    • AAt least SPF30Answer
    • BAt least SPF6
    • CAny factor will do
    • DSunscreen is not needed on site

    Use at least factor 30 on anything you cannot cover with clothing. Shade at breaks and plenty of water matter just as much. Sunscreen is the last line, after keeping your top on and getting out of the sun.

    Sourcehttps://www.hse.gov.uk/skin/sunprotect.htm

  94. 94. Occupational healthcscs-48

    Which hat gives the best protection to an outdoor worker in strong sun?

    • AA cap with a peak at the front
    • BOne with a brim or flap over ears and neckAnswer
    • CA woollen hat pulled down low
    • DAny hat, as long as it is light coloured

    The neck and the ears burn because nothing shades them. A brim or a flap covers both, which a front peak does not. Also check your skin now and then and see a doctor about any mole that changes.

    Sourcehttps://www.hse.gov.uk/skin/sunprotect.htm

  95. 95. Occupational healthcscs-49

    Why is carbon monoxide so hard to notice before it harms you?

    • AIt is colourless, odourless and tastelessAnswer
    • BIt stings the eyes before it builds up
    • CIt only forms outdoors in cold weather
    • DIt smells of petrol at low levels

    Nothing warns you, and the gas comes from fuel that has not burned fully. It stops your blood carrying oxygen and the level can rise fast. Detectors and proper ventilation do the job your senses cannot.

    Sourcehttps://www.hse.gov.uk/construction/healthrisks/hazardous-substances/carbon-monoxide.htm

  96. 96. Occupational healthcscs-50

    A petrol cut off saw is about to be used inside a basement. What is the rule?

    • AIt is fine if the door is left open
    • BIt is fine for short jobs of a few minutes
    • CDo not use petrol plant in enclosed spacesAnswer
    • DIt is fine if the operator wears a mask

    Petrol plant indoors or in a trench builds up dangerous levels within minutes and a dust mask does nothing against gas. Use electric or cordless kit instead. If it truly cannot be avoided, the ventilation has to be assessed by someone who knows how.

    Sourcehttps://www.hse.gov.uk/construction/healthrisks/hazardous-substances/carbon-monoxide.htm

  97. 97. Occupational healthcscs-51

    Two workers in a site cabin with a gas heater feel sick and have headaches. Why is this easy to miss?

    • AThe symptoms look like flu or tirednessAnswer
    • BHeadaches are normal at the end of a long shift
    • COnly one person is usually affected
    • DThe symptoms take weeks to appear

    Drowsiness, headache and nausea get put down to a bug or a late night, so people stay in the room. Yellow or orange flames and sooty marks around the appliance are the physical clues. Get out into fresh air and get the appliance checked.

    Sourcehttps://www.hse.gov.uk/construction/healthrisks/hazardous-substances/carbon-monoxide.htm

  98. 98. Occupational healthcscs-52

    What are the three main ways a hazardous substance gets into your body at work?

    • ALungs, skin and mouthAnswer
    • BEars, eyes and hair
    • CBones, muscles and joints
    • DClothing, boots and gloves

    Dust and vapour are breathed in, some substances soak through skin or attack it, and others are swallowed off dirty hands. Knowing the route tells you which control works. A mask does nothing about cement on your knees.

    Sourcehttps://www.hse.gov.uk/construction/healthrisks/hazardous-substances/key-points.htm

  99. 99. Occupational healthcscs-53

    Why does eating or smoking with unwashed hands matter on a site with lead dust?

    • AIt wastes time in the rest area
    • BYou swallow the dust off your handsAnswer
    • CIt leaves marks on the food
    • DLead only harms you if you breathe it

    The mouth is a real route into the body, and lead builds up in you over time. Washing hands and forearms before eating, drinking or smoking closes it. Taking breaks away from the work area keeps the dust out of the food.

    Sourcehttps://www.hse.gov.uk/construction/healthrisks/hazardous-substances/lead.htm

  100. 100. Occupational healthcscs-54

    You have been stripping old leaded paint all week. What should you not do with your work clothing?

    • ALeave it in a bag on site
    • BWash it at home with the family washAnswer
    • CWear it only in the work area
    • DThrow away disposable coveralls

    Washing contaminated clothes at home spreads lead dust to the people you live with, including children. Keep the work clothing away from your own clothes and take it off before going to the rest area. Disposable coveralls are there to be thrown away.

    Sourcehttps://www.hse.gov.uk/construction/healthrisks/hazardous-substances/lead.htm

Other parts of the Health and Safety Test (CSCS)